Search Results

Vehicle rollovers are one of the more severe crash modes in the US - accounting for 32% of all passenger vehicle occupant fatalities annually. One design enhancement to help prevent rollovers is Electronic Stability Control (ESC) which can reduce loss of control and thus has great promise to enhance vehicle safety. The objectives of this research were (1) to estimate the effectiveness of ESC in reducing the number of rollover crashes and (2) to identify cases in which ESC did not prevent the rollover to potentially advance additional ESC development. All passenger vehicles and light trucks and vans that experienced a rollover from 2006 to 2015 in the National Automotive Sampling System Crashworthiness Database System (NASS/CDS) were analyzed. Each rollover was assigned a crash scenario based on the crash type, pre-crash maneuver, and pre-crash events.

This paper describes a three part analysis to characterize the interaction between the female upper extremity and a helicopter cockpit side airbag system and to develop dynamic hyperextension injury criteria for the female elbow joint. Part I involved a series of 10 experiments with an original Army Black Hawk helicopter side airbag. A 5th percentile female Hybrid III instrumented upper extremity was used to demonstrate side airbag upper extremity loading. Two out of the 10 tests resulted in high elbow bending moments of 128 Nm and 144 Nm. Part II included dynamic hyperextension tests on 24 female cadaver elbow joints. The energy source was a drop tower utilizing a three-point bending configuration to apply elbow bending moments matching the previously conducted side airbag tests. Post-test necropsy showed that 16 of the 24 elbow joint tests resulted in injuries.

The advent of low emission regulations on fuel systems has made conventional sealing materials such as acry-lonitrile butadiene rubber (NBR) unfit for sealing most fuel systems. Therefore, it is imperative to look beyond conventional rubbers and towards more exotic materials to seal such applications. In this study, the permeation characteristics and the change in physical properties of several elastomeric materials (NBR, hydrogenated NBR (HNBR), and fluorocarbon elastomers (FKM)) as well as various poly(tetrafluoroethylene) (PTFE) composites were evaluated with four different fuel mixtures. The sealing materials were tested using vaporimeter cups. The results are discussed as a function of the materials' nature, composition, and filler content.

Event data recorders (EDRs) must survive regulatory frontal and side compliance crash tests if installed within a car or light truck built on or after September 1, 2012. Although previous research has shown that EDR data are surviving these tests, little is known about whether EDRs are capable of surviving collisions of higher delta-v, or crashes involving vehicle fire or immersion. The goal of this study was to determine the survivability of light vehicle EDRs in real world fire, immersion, and high change in velocity (delta-v) cases. The specific objective was to identify the frequency of these extreme events and to determine the EDR data download outcome when subject to damage caused by these events. This study was performed using three crash databases: the Fatality Analysis Reporting System (FARS), the National Automotive Sampling System / Crashworthiness Data System (NASS/CDS), and the National Motor Vehicle Crash Causation Survey (NMVCCS).

Tire modeling plays an important role in the development of an Active Vehicle Safety System. As part of a larger project that aims at developing an integrated chassis control system, this study investigates the performance of a 19” all-season tire on ice for a sport utility vehicle. A design of experiment has been formulated to quantify the effect of operational parameters, specifically: wheel slip, normal load, and inflation pressure on the tire tractive performance. The experimental work was conducted on the Terramechanics Rig in the Advanced Vehicle Dynamics Laboratory at Virginia Tech. The paper investigates an approach for the parameterization of the Dugoff tire model based on the experimental data collected. Compared to other models, this model is attractive in terms of its simplicity, low number of parameters, and easy implementation for real-time applications.

In this investigation an innovative signal generator will be introduced, which enables the generation of transient control signals for the gearshift process. The signals are generated merely depending on scalar transmission control unit (TCU) calibration parameters. The signal generator replaces the comprehensive TCU software within the simulation environment. Thus no extensive residual bus simulation is required. Multiple experimental models represent the core part of the signal generator. To predict the system behavior of the underlying system, the models are trained using measured data from a powertrain with automatic transmission mounted on a test rig. The results demonstrate that the introduced signal generator is suitable to predict transient control signals for the gearshift operation accurately. In combination with an additional powertrain model it is possible to simulate the gearshift process and subsequently to evaluate the gearshift comfort.

This paper presents a novel infrastructural traffic monitoring approach that estimates traffic information by combining two sensing techniques. The traffic information can be obtained from the presented approach includes passing vehicle counts, corresponding speed estimation and vehicle classification based on size. This approach uses measurement from an array of Lidars and video frames from a camera and derives traffic information using two techniques. The first technique detects passing vehicles by using Lidars to constantly measure the distance from laser transmitter to the target road surface. When a vehicle or other objects pass by, the measurement of the distance to road surface reduces in each targeting spot, and triggers detection event. The second technique utilizes video frames from camera and performs background subtraction algorithm in each selected Region of Interest (ROI), which also triggers detection when vehicle travels through each ROI.

A new and unique electric vehicle powertrain model based on bidirectional power flow for propel and regenerative brake power capture is developed and applied to production battery electric vehicles. The model is based on a Willans line model to relate power input from the battery and power output to tractive effort, with one set of parameters (marginal efficiency and an offset loss) for the bidirectional power flow through the powertrain. An electric accessory load is included for the propel, brake and idle phases of vehicle operation. In addition, regenerative brake energy capture is limited with a regen fraction (where the balance goes to friction braking), a power limit, and a low-speed cutoff limit. The purpose of the model is to predict energy consumption and range using only tractive effort based on EPA published road load and test mass (test car list data) and vehicle powertrain parameters derived from EPA reported unadjusted UDDS and HWFET energy consumption.

This paper documents a simple theoretical analysis and an experimental performance comparison of the advantages of an 8-post shaker rig relative to a conventional 7-post shaker rig. A simple static model describing the chassis roll and warp characteristics is first presented to illustrate the differences between 7-post and 8-post configurations, and the conditions where an additional aeroloader provides an advantage. Using a late model NASCAR Sprint Cup car, a series of experimental tests were conducted with the 8-post shaker rig at the Virginia Institute for Performance Engineering and Research (VIPER) facility in both 7-post and 8-post configurations. Experimental results confirm the hypothesis that an 8-post configuration is able to more accurately reproduce target motions of the chassis and suspension when those motions include a chassis warp condition.

The underlying basic model represents a powertrain with automatic transmission including a torque converter. It is based on a greybox-modeling approach, which refers to ordinary differential equations with identified parameters and characteristic curves. The validated basic model is extended in order to reproduce the system behavior and especially the side shaft torque during a gear shift process. Therefore the model is extended by a transmission model with clutches for gear shifting in order to simulate specific powertrain dynamics additionally. The parameters have already been determined for the basic model using a method for isolated and structured parameter identification based on measurement data of an automotive powertrain test bench. A comparable structured parameter identification method is applied to obtain the parameters of the extended model.

Besides optimal engine systems, high-efficiency vehicle transmissions are generally also required to improve fuel economy in automotive applications. For the energy loss analysis in transmissions, most research focused on the major mechanical components, such as gears, bearings and seals, while the other mechanical losses, like synchronizer losses, were usually not considered. With increasing number of synchronizers in modern transmissions, a recent study indicates that the power loss analysis of synchronizers should also be developed and appended for a more accurate investigation on overall power losses in transmissions. The function of synchronizer is to equalize the different rotational speeds of shafts and gear wheels by frictional torques, for which the synchronizer must be cooled and lubricated in order to enhance the service life. With the supplement of lubricants, fluid friction is generated due to the differential speed, when the synchronizer is in neutral position.

The rise of Software-Defined Vehicles (SDV) has rapidly advanced the development of Advanced Driver Assistance Systems (ADAS), Autonomous Vehicle (AV), and Battery Electric Vehicle (BEV) technology. While AVs need power to compute data from perception to controls, BEVs need the efficiency to optimize their electric driving range and stand out compared to traditional Internal Combustion Engine (ICE) vehicles. AVs possess certain shortcomings in the current world, but SAE Level 2+ (L2+) Automated Vehicles are the focus of all major Original Equipment Manufacturers (OEMs). The most common form of an SDV today is the amalgamation of AV and BEV technology on the same platform which is prominently available in most OEM’s lineups. As the compute and sensing architectures for L2+ automated vehicles lean towards a computationally expensive centralized design, it may hamper the most important purchasing factor of a BEV, the electric driving range.

Driver Assistance and Autonomous Driving features are becoming nearly ubiquitous in new vehicles. The intent of the Driver Assistant features is to assist the driver in making safer decisions. The intent of Autonomous Driving features is to execute vehicle maneuvers, without human intervention, in a safe manner. The overall goal of Driver Assistance and Autonomous Driving features is to reduce accidents, injuries, and deaths with a comforting driving experience. However, different drivers can react differently to advanced automated driving technology. It is therefore important to consider and improve the adaptability of these advances based on driver behavior. In this paper, a human-centric approach is adopted to provide an enriching driving experience. We perform data analysis of the naturalistic behavior of drivers when performing lane change maneuvers by extracting features from extensive Second Strategic Highway Research Program (SHRP2) data of over 5,400,000 data files.

In the evolving landscape of automated driving systems, the critical role of vehicle localization within the autonomous driving stack is increasingly evident. Traditional reliance on Global Navigation Satellite Systems (GNSS) proves to be inadequate, especially in urban areas where signal obstruction and multipath effects degrade accuracy. Addressing this challenge, this paper details the enhancement of a localization system for autonomous public transport vehicles, focusing on mitigating GNSS errors through the integration of a LiDAR sensor. The approach involves creating a 3D map using the factor graph-based LIO-SAM algorithm based on GNSS, vehicle odometry, IMU and LiDAR data. The algorithm is adapted to the use-case by adding a velocity factor and altitude data from a Digital Terrain model. Based on the map a state estimator is proposed, which combines high-frequency LiDAR odometry based on FAST-LIO with low-frequency absolute multiscale ICP-based LiDAR position estimation.

Suspension systems are an integral part of land vehicles and contribute significantly to the vehicle performance in terms of its ride comfort and road holding characteristics. In the case of Space Exploration Vehicles (SEVs), the requirement of these unmanned vehicles is to rove, collect pictures and transmit data back to the earth. This is generally performed with the help of exteroceptive, and proprioceptive sensors mounted on the main chassis of the SEV. The design of various components of such vehicles is dictated by the assumption of extreme terrain and environmental conditions that it might face. The Mars Exploration Rovers (MERs) have incorporated the use of the “Rocker-Bogie” mechanism for the suspension system which provides relative stability to the MER for various maneuvers. In this work, the “Rocker-Bogie” mechanism is modeled and simulated as a planar kinematic model using parameters of the Perseverance rover.

Forward Collision Warning (FCW) and Lane Departure Warning (LDW) systems are two active safety systems that have recently been added to the U.S. New Car Assessment Program (NCAP) evaluation. Vehicles that pass confirmation tests may advertise the presence of FCW and LDW alongside the vehicle's star safety rating derived from crash tests. This paper predicts the number of crashes and injured drivers that could be prevented if all vehicles in the U.S. fleet were equipped with production FCW and/or LDW systems. Models of each system were developed using the test track data collected for 16 FCW and 10 LDW systems by the NCAP confirmation tests. These models were used in existing fleetwide benefits models developed for FCW and LDW. The 16 FCW systems evaluated could have potentially prevented between 9% and 53% of all rear-end collisions and prevented between 19% and 60% of injured (MAIS2+) drivers. Earlier warning times prevented more warnings and injuries.

Tire-pavement interaction noise (TPIN) is a dominant source for passenger cars and trucks above 40 km/h and 70 km/h, respectively. TPIN is mainly generated from the interaction between the tire and the pavement. In this paper, twenty-two passenger car radial (PCR) tires of the same size (16 in. radius) but with different tread patterns were tested on a non-porous asphalt pavement. For each tire, the noise data were collected using an on-board sound intensity (OBSI) system at five speeds in the range from 45 to 65 mph (from 72 to 105 km/h). The OBSI system used an optical sensor to record a once-per-revolution signal to monitor the vehicle speed. This signal was also used to perform order tracking analysis to break down the total tire noise into two components: tread pattern-related noise and non-tread pattern-related noise.

Inerters have become a hot topic in recent years, especially in vehicle, train, and building suspension systems. The performance of a passive inerter and a semi-active inerter was analyzed and compared with each other and it showed that the semi-active inerter has much better performance than the passive inerter, especially with the Hybrid control method. Eight different layouts of suspensions were analyzed with a quarter car model in this paper. The adaptation of dimensionless parameters was considered for a semi-active suspension and the semi-active inerters. The performance of the semi-active inerter suspensions with different layouts was compared with a semi-active suspension with a conventional parallel spring-damper arrangement. It shows a semi-active suspension, with more simple configuration and lower cost, has similar or better compromise between ride and handling than a semi-active inerter with the Hybrid control.

Magneto-rheological fluid squeeze mode investigations at CVeSS have shown that MR fluids show large force capabilities in squeeze mode. A novel MR squeeze mount was designed and built at CVeSS, and a dynamic mathematical model was developed, which considered the inertial effect and was validated by the test data. A variant engine mount that will be used for isolating vibration, based on the MR squeeze mode is proposed in the paper. The mathematical governing equations of the mount are derived to account for its operation with MR squeeze mode. The design method of a robust H✓ controller is addressed for the squeeze mount subject to parameter uncertainties in the damping and stiffness. The controller parameter can be derived from the solution of bilinear matrix inequalities (BMIs). The displacement transmissibility is constrained to be no more than 1.05 with this robust H✓ controller. The MR squeeze mount has a very large range of force used to isolate the vibration.